Design Standards

Washington University School of Medicine (WUSM) provides Design & Building Systems Standards to all parties involved in providing design and construction services to WUSM based on preferred products and procedures, as well as current industry practices. WUSM does not guarantee the performance or safety of any products or systems as they are tested, installed, or operated in accordance with these standards.

Introduction

The Design & Building Systems Standards are intended to serve as design and construction standard guidelines for the WUSM campus of Washington University. The Design Standards are divided into two sections: Design Standards (Architectural) and Building Systems Standards (MEPFP). The Design Standards reflect the contributions from planning, design, management, construction, and maintenance expertise of University employees. The standards have been compiled and edited by HKW Architects and SSC Engineering, Inc.

As Design Standards for WUSM, this information applies to both new construction and renovation projects. Guidelines for meetings and collaboration are outlined from the initial planning and design stages, through the construction process, and into the maintenance and management period. Information included within each section includes materials and products to use, procedures, and design guidelines that the institution has found to be appropriate for the level of quality desired and for future maintenance of these facilities. Architects, Consultants, Contractors, and Facilities Personnel should become familiar with these standards.

Scope of the standards

Design Standards shall serve as a basis for quality for all campus-wide design, construction, and maintenance procedures. The information within these standards is not specific to any one project, but is common to all projects. Because WUSM constructs a wide variety of facilities, these standards must be adjusted as necessary to meet the specific project needs. The standards establish a baseline of quality, and it is WUSM’s expectation that any deviations from these standards will be discussed with Capital Projects and the WUSM Project Manager throughout the design process. All drawings will be reviewed for conformance to these standards.

Standards versus specifications

Design Standards shall form the basis from which to create specifications. The use and inclusion of these standards in bid documents does not relieve the Architect or Consultant of the responsibility and legal liability for any bid documents created from these standards.

A living document

Design Standards from all areas of design and construction are continually being developed. As changes and new sections are ready for inclusion, changes will be made to these standards, and revision dates will be clearly noted. The Design Standards are maintained by WUSM Operations & Facilities Management Department, Washington University School of Medicine, 660 South Euclid Avenue, Campus Box 8010, Saint Louis, Missouri, 63110. All feedback is welcome and appreciated: wusmfacilities@wusm.wustl.edu. More information about the design standards can be found in the general information document.

General Design Standards

01 Accessibility
02 Custodial
03 Emergency preparedness
04 Specialized facilities
05 Sustainability
06 Wood plastic composites
07 Thermal & moisture protection
08 Openings
09 Finishes
10 Specialties
11 Equipment
12 Furnishings
14 Conveying

Mechanical

00 TOC Mechanical
01 Mechanical General Requirements
02 Air Filtration
03 Air Handling Units
04 Air Valves
05 Breechings, Chimneys, & Stacks
06 Chillers
07 Cleaning of Piping Systems
08 Commissioning
09 Condensing Boilers
10 Cooling Towers
11 DDC Controls
12 Ductwork
13 Fan Coil Units
14 Hangers and Supports
15 Heat Exchangers – Airside
16 Heat Exchangers – Hydronic
17 HVAC Fans – Laboratory
18 HVAC Fans – Non-Laboratory
19 HVAC Water Treatment
20 Identification
21 Insulation
22 Laboratory Fume Hoods
23 Piping and Valves – Hydronic
24 Piping and Valves – Steam
25 Pumps – Hydronic
26 Pumps – Steam Condensate
27 Terminal Units

Electrical

00 TOC Electrical
01 Basic Electrical Materials and Methods
02 Building Wire and Cable
03 Grounding and Bonding
04 Conduits, Fittings and Boxes
05 Identification for Electrical Systems
06 Lighting Controls
07 Service and Distribution
08 5kV Switches
09 Panelboards
10 Transformers
11 Switchboards
12 Circuit Breakers
13 Wiring Devices
14 Enclosed Motor Controllers
15 Motors
16 Enclosed Switches and Enclosed Circuit Breakers
17 Variable Frequency Drives
18 Emergency Power Supply
19 ATSs
20 Interior Lighting
21 Exterior Lighting
22 Low Voltage
23 Security Access System
24 Fire Alarm Systems
25 Nurse Call Systems

Plumbing

00 TOC Plumbing
1 General Requirements
2 Equipment
3 Fixtures
4 Lab Piping
5 Sanitary Waste, Vent and Storm Piping
6 Water Piping
7 RODI Equipment

Fire protection

00 TOC Fire Protection
WUSM Fire Protection Standards

Lactation Rooms

Lactation Room Design Standards

Low Voltage Voice and Data

Low Voltage Voice and Data

A/V

AV Standards

BSL3 & ABSL3

BSL3 Design Guidelines

Design & AV Guidelines

Design and AV Guidelines
Samples for AV and Furniture Design Guidelines for Classroom and Meeting Spaces